.国产短视频

国产短视频

国产短视频College of Marine Science

News

Device built from scratch helps scientists tackle a fish-spawning mystery

The CUFES鈥 first day out at sea collecting fish eggs as the Weatherbird II is underway heading north to the panhandle. Picture Credit: Jess Van Vaerenbergh

The CUFES during its first day out at sea collecting fish eggs as the Weatherbird II traveled north to the panhandle. Picture Credit: Jess Van Vaerenbergh

Written by: Jess Van Vaerenbergh, 国产短视频CMS graduate student

Researchers have long known that fish reproduce in the Gulf of Mexico, but which species spawn where remains a mystery.

Researchers at the 国产短视频College of Marine Science (CMS) may soon solve that mystery thanks to , a graduate student in biological oceanography at CMS, and an unassuming device called a CUFES (pronounced, coofs).

The CUFES 鈥 short for Continuous Underway Fish Egg Sampler 鈥 is a device that鈥檚 smaller than a mini fridge with long, flexible tubes to suck up seawater.

The original CUFES was invented in 1993 by biologist to study fish spawning patterns in California. After a successful trial run on a (NOAA) vessel, a long-term collaboration was created with , the , and (SIO).

Four decades later, CUFES devices have helped track fish spawning and manage fisheries around the world.

The CUFES operates by using a pump to draw in water from the side of the vessel. This water is then pushed through a large flexible hose into a box called a concentrator. Inside the concentrator, the seawater is filtered through a fine mesh bag, which allows the eggs to remain. The eggs are then directed into a small clear tube and collected in a container.

Every 30 minutes, the crew empties the sample into small vials.

When researchers at CMS wanted a new way to study spawning in the Gulf of Mexico, Christopher Stallings, a professor of biological oceanography, had a bold idea: why not build a CUFES from scratch?

Miller, a student in with a knack for engineering and an apprentice in the machine shop on the CMS campus, were up to the challenge.

Miller and other members of Stallings's lab first tried to track down the blueprint but all they had was a photo of NOAA鈥檚 CUFES. Undeterred, graduate student Ian Williams, who worked with the original device in previous research, traveled to the in Pascagoula, Mississippi, and brought an original CUFES back to St. Petersburg, where Miller used it as a model.

Miller spent the next few days recording each measurement on a yellow notepad to create a rough guide.

"I had to measure every single part of the machine by hand,鈥 Miller said. 鈥淓ach opening, the thickness of each piece of metal, and even each screw. We had to measure within one one-thousandth of an inch, so a tape measure was no longer the appropriate tool.鈥

During the initial welding process of the main CUFES box, Miller used clamps to apply pressure in specific directions to prevent the metal from warping as it cooled. This also allowed for small, short welds to make sure the structure was aligned before the final weld. Picture Credit: Garret Miller

During the initial welding process of the main CUFES box, Miller used clamps to apply pressure in specific directions to prevent the metal from warping as it cooled. This also allowed for small, short welds to make sure the structure was aligned before the final weld. Picture Credit: Garret Miller

Miller turned instead to a specialized tool called a micrometer.

鈥淥ur most precise micrometers can actually even measure down to within a tenth of a thousandth of an inch,鈥 he said. 鈥淭hat鈥檚 super tiny.鈥

Miller spent hours in the machine shop at CMS constructing the new device from scratch. Miller, alongside fellow machinists Jim Mulhollan and Guy Grant, faithfully recreated the CUFES piece by piece, while also making a few upgrades. With help from colleagues, including the engineers at the Ocean Technology Group, he used a variety of skills and tools to turn the rough sketch into a fully functioning device in just four months.

In late June, a crew of four from CMS took the CUFES on its maiden voyage across the entire West Florida Shelf aboard the . Williams, who served as chief scientist, and I represented the Stallings lab. Alexis Mitchem and AJ Gross participated as members of the lab of Mya Breitbart, a Distinguished University Professor of biological oceanography at CMS.

The CUFES ran 24/7 while the crew traveled 2,200 miles over 11 days to collect fish eggs from the Florida panhandle to the Dry Tortugas. The device persevered through the elements despite ingesting a few pieces of sargassum and one unfortunate flying fish.

The eggs it collected will be analyzed at the college by the .

The CUFES ran around the clock collecting samples 鈥 and so did the crew. Those that worked through the night witnessed colorful sunrises every morning. Picture Credit: Jess Van Vaerenbergh

The CUFES ran around the clock collecting samples 鈥 and so did the crew. Those that worked through the night witnessed colorful sunrises every morning. Picture Credit: Jess Van Vaerenbergh

The data collected on the cruise will contribute to the Spawning Habitat & Early-Life Linkages to Fisheries (SHELF) project, which is funded by the (FLRACEP) under the . The SHELF project seeks to determine the timing and locations of spawning fishes in the Gulf of Mexico by using DNA from the collected eggs.

The crew collected a diverse set of samples over 11 days. These are just two examples, one which included a mix of phytoplankton and fish eggs, and the other with crab larvae. Picture Credit: Jess Van Vaerenbergh

The crew collected a diverse set of samples over 11 days. These are just two examples, one which included a mix of phytoplankton and fish eggs, and the other with crab larvae. Picture Credit: Jess Van Vaerenbergh

CMS researchers aim to develop a dataset for monitoring changes in the spawning efforts and locations of important fish species that can be affected by climate change, fishing, and habitat quality.

Williams will use the CUFES to study eggs collected from a reef system where the Stallings lab conducts seasonal visual reef fish surveys. By comparing the collected eggs to the adult abundances of certain species, William hopes to reveal how fish use the reefs for reproduction.

, working in the Breitbart lab, will focus on using DNA from each egg to identify fish species.

Future work will include cruises through 2026 to compare the results seasonally and annually, providing a better understanding of when and where certain fish species are spawning across the West Florida Shelf.

The crew was welcomed back to campus after 11 days at sea collecting fish eggs for the SHELF project. Photo credit: Mya Breitbart

The crew was welcomed back to campus after 11 days at sea collecting fish eggs for the SHELF project. Photo credit: Mya Breitbart

As CMS researchers continue their study, the CUFES will play a crucial role in unraveling the mysteries of fish spawning in the Gulf of Mexico.

Each expedition gathers valuable data that will significantly contribute to the SHELF project's goal of understanding the spawning efforts and patterns of important fish species.

The construction of the CUFES was not only a notable achievement for Miller and his colleagues, but also a symbol of the dedication to understanding our marine environments that drives CMS researchers forward.

Return to article listing

Mission Statement

Our blue planet faces a suite of challenges and opportunities for understanding and innovation. Our mission is to advance understanding of the interconnectivity of ocean systems and human-ocean interactions using a cross-disciplinary approach, to empower the next workforce of the blue economy with a world-class education experience, and to share our passion for a healthy environment and science-informed decision-making with community audiences near and far.